perlsub - indicate version requirement for "delete local"

[perl5.git] / README.netware

diff --git a/README.netware b/README.netware
index c5299e3..4e35f39 100644 (file)
--- a/README.netware
+++ b/README.netware
@@ -48,14 +48,25 @@ sets the build type to Release by default.
 This is used to set the build type to debug or release. Change the
 build type only after executing SetNWBld.bat
 
-=item *
-
 Example:
-  1. Typing "buildtype d on" at the command prompt causes the buildtype
-     to be set to Debug type with D2 flag set. 
-  2. Typing "buildtype d off" or "buildtype d" at the command prompt causes
-     the buildtype to be set to Debug type with D1 flag set. 
-  2. Typing "buildtype r" at the command prompt sets it to Release Build type.
+
+=over
+
+=item 1.
+
+Typing "buildtype d on" at the command prompt causes the buildtype
+to be set to Debug type with D2 flag set. 
+
+=item 2.
+
+Typing "buildtype d off" or "buildtype d" at the command prompt causes
+the buildtype to be set to Debug type with D1 flag set. 
+
+=item 3.
+
+Typing "buildtype r" at the command prompt sets it to Release Build type.
+
+=back
 
 =back
 
@@ -107,8 +118,8 @@ I<sys:\perl\system> folder.  Copy this to I<sys:\system> folder.
 
 Example: At the command prompt Type "nmake nwinstall".
           This will install NetWare Perl on the NetWare Server.
-          Similiarly if you type "nmake install",
-          This will cause the binaries to be installed on the local machine.
+          Similarly, if you type "nmake install",
+          this will cause the binaries to be installed on the local machine.
           (Typically under the c:\perl folder)
 
 =head1 BUILD NEW EXTENSIONS
@@ -140,11 +151,13 @@ Run the following command at the command prompt:
 
 Example:
 
-    perl -Ic:/perl/5.6.1/lib/NetWare-x86-multi-thread -Ic:\perl\5.6.1\lib MakeFile.pl
+    perl -Ic:/perl/5.6.1/lib/NetWare-x86-multi-thread           \
+                                -Ic:\perl\5.6.1\lib MakeFile.pl
 
 or
 
-    perl -Ic:/perl/5.8.0/lib/NetWare-x86-multi-thread -Ic:\perl\5.8.0\lib MakeFile.pl
+    perl -Ic:/perl/5.8.0/lib/NetWare-x86-multi-thread           \
+                                -Ic:\perl\5.8.0\lib MakeFile.pl
 
 =item *
 
@@ -163,13 +176,15 @@ typing I<nmake install>, will copy the files onto the NetWare server.
 
 Example: You can execute the following on the command prompt.
 
-          perl -Ic:/perl/5.6.1/lib/NetWare-x86-multi-thread -Ic:\perl\5.6.1\lib MakeFile.pl
-          INSTALLSITELIB=i:\perl\lib
+  perl -Ic:/perl/5.6.1/lib/NetWare-x86-multi-thread             \
+                                -Ic:\perl\5.6.1\lib MakeFile.pl
+  INSTALLSITELIB=i:\perl\lib
 
 or
 
-          perl -Ic:/perl/5.8.0/lib/NetWare-x86-multi-thread -Ic:\perl\5.8.0\lib MakeFile.pl
-          INSTALLSITELIB=i:\perl\lib
+  perl -Ic:/perl/5.8.0/lib/NetWare-x86-multi-thread             \
+                                -Ic:\perl\5.8.0\lib MakeFile.pl
+  INSTALLSITELIB=i:\perl\lib
 
 =item *